How To Install Nagios 4 and Monitor Your Servers on CentOS 7

Introduction

In this tutorial, we will cover the installation of Nagios 4, a very popular open source monitoring system, on CentOS 7 or RHEL 7. We will cover some basic configuration, so you will be able to monitor host resources via the web interface. We will also utilize the Nagios Remote Plugin Executor (NRPE), that will be installed as an agent on remote hosts, to monitor their local resources.

Nagios is useful for keeping an inventory of your servers, and making sure your critical services are up and running. Using a monitoring system, like Nagios, is an essential tool for any production server environment.

Prerequisites

To follow this tutorial, you must have superuser privileges on the CentOS 7 server that will run Nagios. Ideally, you will be using a non-root user with superuser privileges. If you need help setting that up, follow the steps 1 through 3 in this tutorial: Initial Server Setup with CentOS 7.

A LAMP stack is also required. Follow this tutorial if you need to set that up: How To Install LAMP stack On CentOS 7.

This tutorial assumes that your server has private networking enabled. If it doesn’t, just replace all the references to private IP addresses with public IP addresses.

Now that we have the prerequisites sorted out, let’s move on to getting Nagios 4 installed.

Install Nagios 4

This section will cover how to install Nagios 4 on your monitoring server. You only need to complete this section once.

Install Build Dependencies

Because we are building Nagios Core from source, we must install a few development libraries that will allow us to complete the build.

First, install the required packages:

sudo yum install gcc glibc glibc-common gd gd-devel make net-snmp openssl-devel xinetd unzip

Create Nagios User and Group

We must create a user and group that will run the Nagios process. Create a “nagios” user and “nagcmd” group, then add the user to the group with these commands:

sudo useradd nagios
sudo groupadd nagcmd
sudo usermod -a -G nagcmd nagios

Let’s install Nagios now.

Install Nagios Core

Download the source code for the latest stable release of Nagios Core. Go to the Nagios downloads page, and click the Skip to download link below the form. Copy the link address for the latest stable release so you can download it to your Nagios server.

At the time of this writing, the latest stable release is Nagios 4.1.1. Download it to your home directory with curl:

cd ~
curl -L -O https://assets.nagios.com/downloads/nagioscore/releases/nagios-4.1.1.tar.gz

Extract the Nagios archive with this command:

tar xvf nagios-*.tar.gz

Then change to the extracted directory:

cd nagios-*

Before building Nagios, we must configure it with this command:

./configure --with-command-group=nagcmd 

Now compile Nagios with this command:

make all

Now we can run these make commands to install Nagios, init scripts, and sample configuration files:

sudo make install
sudo make install-commandmode
sudo make install-init
sudo make install-config
sudo make install-webconf

In order to issue external commands via the web interface to Nagios, we must add the web server user, apache, to the nagcmd group:

sudo usermod -G nagcmd apache

Install Nagios Plugins

Find the latest release of Nagios Plugins here: Nagios Plugins Download. Copy the link address for the latest version, and copy the link address so you can download it to your Nagios server.

At the time of this writing, the latest version is Nagios Plugins 2.1.1. Download it to your home directory with curl:

cd ~
curl -L -O http://nagios-plugins.org/download/nagios-plugins-2.1.1.tar.gz

Extract Nagios Plugins archive with this command:

tar xvf nagios-plugins-*.tar.gz

Then change to the extracted directory:

cd nagios-plugins-*

Before building Nagios Plugins, we must configure it. Use this command:

./configure --with-nagios-user=nagios --with-nagios-group=nagios --with-openssl

Now compile Nagios Plugins with this command:

make

Then install it with this command:

sudo make install

Install NRPE

Find the source code for the latest stable release of NRPE at the NRPE downloads page. Download the latest version to your Nagios server.

At the time of this writing, the latest release is 2.15. Download it to your home directory with curl:

cd ~
curl -L -O http://downloads.sourceforge.net/project/nagios/nrpe-2.x/nrpe-2.15/nrpe-2.15.tar.gz

Extract the NRPE archive with this command:

tar xvf nrpe-*.tar.gz

Then change to the extracted directory:

cd nrpe-*

Configure NRPE with these commands:

./configure --enable-command-args --with-nagios-user=nagios --with-nagios-group=nagios --with-ssl=/usr/bin/openssl --with-ssl-lib=/usr/lib/x86_64-linux-gnu

Now build and install NRPE and its xinetd startup script with these commands:

make all
sudo make install
sudo make install-xinetd
sudo make install-daemon-config

Open the xinetd startup script in an editor:

sudo vi /etc/xinetd.d/nrpe

Modify the only_from line by adding the private IP address of the your Nagios server to the end (substitute in the actual IP address of your server):

only_from = 127.0.0.1 10.132.224.168

Save and exit. Only the Nagios server will be allowed to communicate with NRPE.

Restart the xinetd service to start NRPE:

sudo service xinetd restart

Now that Nagios 4 is installed, we need to configure it.

Configure Nagios

Now let’s perform the initial Nagios configuration. You only need to perform this section once, on your Nagios server.

Organize Nagios Configuration

Open the main Nagios configuration file in your favorite text editor. We’ll use vi to edit the file:

sudo vi /usr/local/nagios/etc/nagios.cfg

Now find an uncomment this line by deleting the #:

#cfg_dir=/usr/local/nagios/etc/servers

Save and exit.

Now create the directory that will store the configuration file for each server that you will monitor:

sudo mkdir /usr/local/nagios/etc/servers

Configure Nagios Contacts

Open the Nagios contacts configuration in your favorite text editor. We’ll use vi to edit the file:

sudo vi /usr/local/nagios/etc/objects/contacts.cfg

Find the email directive, and replace its value (the highlighted part) with your own email address:

email                           nagios@localhost        ; <<***** CHANGE THIS TO YOUR EMAIL ADDRESS ******

Save and exit.

Configure check_nrpe Command

Let’s add a new command to our Nagios configuration:

sudo vi /usr/local/nagios/etc/objects/commands.cfg

Add the following to the end of the file:

define command{
        command_name check_nrpe
        command_line $USER1$/check_nrpe -H $HOSTADDRESS$ -c $ARG1$
}

Save and exit. This allows you to use the check_nrpe command in your Nagios service definitions.

Configure Apache

Use htpasswd to create an admin user, called “nagiosadmin”, that can access the Nagios web interface:

sudo htpasswd -c /usr/local/nagios/etc/htpasswd.users nagiosadmin

Enter a password at the prompt. Remember this login, as you will need it to access the Nagios web interface.

Nagios is ready to be started. Let’s do that, and restart Apache:

sudo systemctl daemon-reload
sudo systemctl start nagios.service
sudo systemctl restart httpd.service

To enable Nagios to start on server boot, run this command:

sudo chkconfig nagios on

Optional: Restrict Access by IP Address

If you want to restrict the IP addresses that can access the Nagios web interface, you will want to edit the Apache configuration file:

sudo vi /etc/httpd/conf.d/nagios.conf

Find and comment the following two lines by adding # symbols in front of them:

Order allow,deny
Allow from all

Then uncomment the following lines, by deleting the # symbols, and add the IP addresses or ranges (space delimited) that you want to allow to in the Allow from line:

#  Order deny,allow
#  Deny from all
#  Allow from 127.0.0.1

As these lines will appear twice in the configuration file, so you will need to perform these steps once more.

Save and exit.

Now start Nagios and restart Apache to put the change into effect:

sudo systemctl restart nagios.service
sudo systemctl restart httpd.service

Nagios is now running, so let’s try and log in.

Accessing the Nagios Web Interface

Open your favorite web browser, and go to your Nagios server (substitute the IP address or hostname for the highlighted part):

http://nagios_server_public_ip/nagios

Because we configured Apache to use htpasswd, you must enter the login credentials that you created earlier. We used “nagiosadmin” as the username:

After authenticating, you will be see the default Nagios home page. Click on the Hosts link, in the left navigation bar, to see which hosts Nagios is monitoring:

As you can see, Nagios is monitoring only “localhost”, or itself.

Let’s monitor another host with Nagios!

Monitor a CentOS 7 Host with NRPE

In this section, we’ll show you how to add a new host to Nagios, so it will be monitored. Repeat this section for each CentOS or RHEL server you wish to monitor.

Note: If you want to monitor an Ubuntu or Debian server, follow the instructions in this link: Monitor an Ubuntu Host with NRPE.

On a server that you want to monitor, install the EPEL repository:

sudo yum install epel-release

Now install Nagios Plugins and NRPE:

sudo yum install nrpe nagios-plugins-all

Now, let’s update the NRPE configuration file. Open it in your favorite editor (we’re using vi):

sudo vi /etc/nagios/nrpe.cfg

Find the allowed_hosts directive, and add the private IP address of your Nagios server to the comma-delimited list (substitute it in place of the highlighted example):

allowed_hosts=127.0.0.1,10.132.224.168

Save and exit. This configures NRPE to accept requests from your Nagios server, via its private IP address.

Restart NRPE to put the change into effect:

sudo systemctl start nrpe.service
sudo systemctl enable nrpe.service

Once you are done installing and configuring NRPE on the hosts that you want to monitor, you will have to add these hosts to your Nagios server configuration before it will start monitoring them.

Add Host to Nagios Configuration

On your Nagios server, create a new configuration file for each of the remote hosts that you want to monitor in /usr/local/nagios/etc/servers/. Replace the highlighted word, “yourhost”, with the name of your host:

sudo vi /usr/local/nagios/etc/servers/yourhost.cfg

Add in the following host definition, replacing the host_name value with your remote hostname (“web-1” in the example), the alias value with a description of the host, and the address value with the private IP address of the remote host:

define host {
        use                             linux-server
        host_name                       yourhost
        alias                           My first Apache server
        address                         10.132.234.52
        max_check_attempts              5
        check_period                    24x7
        notification_interval           30
        notification_period             24x7
}

With the configuration file above, Nagios will only monitor if the host is up or down. If this is sufficient for you, save and exit then restart Nagios. If you want to monitor particular services, read on.

Add any of these service blocks for services you want to monitor. Note that the value of check_command determines what will be monitored, including status threshold values. Here are some examples that you can add to your host’s configuration file:

Ping:

define service {
        use                             generic-service
        host_name                       yourhost
        service_description             PING
        check_command                   check_ping!100.0,20%!500.0,60%
}

SSH (notifications_enabled set to 0 disables notifications for a service):

define service {
        use                             generic-service
        host_name                       yourhost
        service_description             SSH
        check_command                   check_ssh
        notifications_enabled           0
}

If you’re not sure what use generic-service means, it is simply inheriting the values of a service template called “generic-service” that is defined by default.

Now save and quit. Reload your Nagios configuration to put any changes into effect:

sudo systemctl reload nagios.service

Once you are done configuring Nagios to monitor all of your remote hosts, you should be set. Be sure to access your Nagios web interface, and check out the Services page to see all of your monitored hosts and services:

Conclusion

Now that you monitoring your hosts and some of their services, you might want to spend some time to figure out which services are critical to you, so you can start monitoring those. You may also want to set up notifications so, for example, you receive an email when your disk utilization reaches a warning or critical threshold or your main website is down, so you can resolve the situation promptly or before a problem even occurs.

Good luck!

sudo systemctl restart nagios.service
sudo systemctl restart httpd.service

sudo: systemctl: command not found

service nagios restart
service httpd restart

yum install unzip